Differences

This shows you the differences between two versions of the page.

--- knxnet_ip [2020/01/14 19:04] – ingrid
+++ knxnet_ip [2020/01/14 20:27] – ingrid
@@ Line 12: / Line 12: @@
   * **KNX/IP interface** without routing, allowing KNX programming over IP.
   * **KNX IP router**, allowing KNX programing as well as connecting different parts of a KNX system together over IP, much like a line coupler.
+{{ :knxnet_ip_6.png?direct800 |Thinknx server with KNXNet/IP interface}}
+<WRAP center 60%> <WRAP centeralign> Figure 1: Thinknx server with KNXNet/IP interface</WRAP> </WRAP>
 The Thinknx server can also communicate with other KNXNet/IP interfaces instead of using its own embedded bus connection to communicate with the KNX bus.
@@ Line 33: / Line 36: @@
 {{ :knxnet_ip_1.png?direct800 |Enabling KNXNet/IP Interface from Configurator}}
-<WRAP center 60%> <WRAP centeralign> Figure 1: Enabling KNXNet/IP Interface from Configurator </WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 2: Enabling KNXNet/IP Interface from Configurator </WRAP>  </WRAP>
 ==== Using the webpage ====
@@ Line 39: / Line 42: @@
 {{ :knxnet_ip_2.png?direct800 |Accessing Network and KNX}}
-<WRAP center 60%> <WRAP centeralign> Figure 2: Accessing Network and KNX</WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 3: Accessing Network and KNX</WRAP>  </WRAP>
 Scroll down to reach the "KNX Settings". By default, the web page will show the KNX configuration uploaded with the Thinknx project.
 {{ :knxnet_ip_3a.png?direct800 |Viewing the KNX settings}}
-<WRAP center 60%> <WRAP centeralign> Figure 3: Viewing the KNX settings</WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 4: Viewing the KNX settings</WRAP>  </WRAP>
 If you wish to override these settings, click on "Overridden".
 {{ :knxnet_ip_3.png?direct800 |Editing the KNX settings}}
-<WRAP center 60%> <WRAP centeralign> Figure 4: Editing the KNX settings</WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 5: Editing the KNX settings</WRAP>  </WRAP>
 The below parameters are available to configure:
@@ Line 73: / Line 76: @@
 {{ :knxnet_ip_4.png?direct800 |Scanning server from ETS}}
-<WRAP center 60%> <WRAP centeralign> Figure 5: Scanning server from ETS</WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 6: Scanning server from ETS</WRAP>  </WRAP>
 ===== Application 2: Thinknx server as KNXnet/IP Router =====
@@ Line 80: / Line 83: @@
 <WRAP column half>
 {{ :knxnet_ip_5b.png?direct500 |Installation without KNXNet/IP routing}}
-<WRAP center 60%> <WRAP centeralign> Figure 6-a: Installation without KNXNet/IP routing</WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 7-a: Installation without KNXNet/IP routing</WRAP>  </WRAP>
 </WRAP>
 <WRAP column half>
 {{ :knxnet_ip_5c.png?direct500 |Installation with KNXNet/IP routing}}
-<WRAP center 60%> <WRAP centeralign> Figure 6-b: Installation with KNXNet/IP routing</WRAP>  </WRAP>
+<WRAP center 60%> <WRAP centeralign> Figure 7-b: Installation with KNXNet/IP routing</WRAP>  </WRAP>
 </WRAP>
 </WRAP>