Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
knxnet_ip [2020/01/14 19:04] – ingrid | knxnet_ip [2020/01/28 08:40] (current) – wikiadmin | ||
---|---|---|---|
Line 12: | Line 12: | ||
* **KNX/IP interface** without routing, allowing KNX programming over IP. | * **KNX/IP interface** without routing, allowing KNX programming over IP. | ||
* **KNX IP router**, allowing KNX programing as well as connecting different parts of a KNX system together over IP, much like a line coupler. | * **KNX IP router**, allowing KNX programing as well as connecting different parts of a KNX system together over IP, much like a line coupler. | ||
+ | |||
+ | {{ : | ||
+ | <WRAP center 60%> <WRAP centeralign> | ||
The Thinknx server can also communicate with other KNXNet/IP interfaces instead of using its own embedded bus connection to communicate with the KNX bus. | The Thinknx server can also communicate with other KNXNet/IP interfaces instead of using its own embedded bus connection to communicate with the KNX bus. | ||
Line 28: | Line 31: | ||
* **Client number** number of supported client tunnel connections. | * **Client number** number of supported client tunnel connections. | ||
<WRAP important center round 80%> When using the server as a KNXnet/IP interface, it is important to define the " | <WRAP important center round 80%> When using the server as a KNXnet/IP interface, it is important to define the " | ||
- | <WRAP important center round 80%> The " | + | <WRAP important center round 80%> The " |
* **KNXNet/IP router** If enabled, the server will also route traffic from TP to multicast IP and vice versa, allowing to connect different parts of a KNX system together over IP. | * **KNXNet/IP router** If enabled, the server will also route traffic from TP to multicast IP and vice versa, allowing to connect different parts of a KNX system together over IP. | ||
<WRAP important center round 80%> Be careful to avoid loops that may result from connecting 2 Thinknx servers with KNXNet/IP router enabled on the same network and same TP line. </ | <WRAP important center round 80%> Be careful to avoid loops that may result from connecting 2 Thinknx servers with KNXNet/IP router enabled on the same network and same TP line. </ | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
==== Using the webpage ==== | ==== Using the webpage ==== | ||
Line 39: | Line 42: | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
Scroll down to reach the "KNX Settings" | Scroll down to reach the "KNX Settings" | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
If you wish to override these settings, click on " | If you wish to override these settings, click on " | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
The below parameters are available to configure: | The below parameters are available to configure: | ||
Line 73: | Line 76: | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
===== Application 2: Thinknx server as KNXnet/IP Router ===== | ===== Application 2: Thinknx server as KNXnet/IP Router ===== | ||
Line 80: | Line 83: | ||
<WRAP column half> | <WRAP column half> | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
</ | </ | ||
<WRAP column half> | <WRAP column half> | ||
{{ : | {{ : | ||
- | <WRAP center 60%> <WRAP centeralign> | + | <WRAP center 60%> <WRAP centeralign> |
</ | </ | ||
</ | </ |