Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
knxnet_ip [2020/01/14 19:04]
ingrid
knxnet_ip [2020/01/14 20:27] (current)
ingrid
Line 12: Line 12:
   * **KNX/IP interface** without routing, allowing KNX programming over IP.   * **KNX/IP interface** without routing, allowing KNX programming over IP.
   * **KNX IP router**, allowing KNX programing as well as connecting different parts of a KNX system together over IP, much like a line coupler. ​   * **KNX IP router**, allowing KNX programing as well as connecting different parts of a KNX system together over IP, much like a line coupler. ​
 +
 +{{ :​knxnet_ip_6.png?​direct800 |Thinknx server with KNXNet/IP interface}}
 +<WRAP center 60%> <WRAP centeralign>​ Figure 1: Thinknx server with KNXNet/IP interface</​WRAP>​ </​WRAP>​
  
 The Thinknx server can also communicate with other KNXNet/IP interfaces instead of using its own embedded bus connection to communicate with the KNX bus. The Thinknx server can also communicate with other KNXNet/IP interfaces instead of using its own embedded bus connection to communicate with the KNX bus.
Line 33: Line 36:
  
 {{ :​knxnet_ip_1.png?​direct800 |Enabling KNXNet/IP Interface from Configurator}} {{ :​knxnet_ip_1.png?​direct800 |Enabling KNXNet/IP Interface from Configurator}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​1: Enabling KNXNet/IP Interface from Configurator </​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​2: Enabling KNXNet/IP Interface from Configurator </​WRAP> ​ </​WRAP>​
  
 ==== Using the webpage ==== ==== Using the webpage ====
Line 39: Line 42:
  
 {{ :​knxnet_ip_2.png?​direct800 |Accessing Network and KNX}} {{ :​knxnet_ip_2.png?​direct800 |Accessing Network and KNX}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​2: Accessing Network and KNX</​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​3: Accessing Network and KNX</​WRAP> ​ </​WRAP>​
  
 Scroll down to reach the "KNX Settings"​. By default, the web page will show the KNX configuration uploaded with the Thinknx project. ​ Scroll down to reach the "KNX Settings"​. By default, the web page will show the KNX configuration uploaded with the Thinknx project. ​
  
 {{ :​knxnet_ip_3a.png?​direct800 |Viewing the KNX settings}} {{ :​knxnet_ip_3a.png?​direct800 |Viewing the KNX settings}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​3: Viewing the KNX settings</​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​4: Viewing the KNX settings</​WRAP> ​ </​WRAP>​
  
 If you wish to override these settings, click on "​Overridden"​. If you wish to override these settings, click on "​Overridden"​.
  
 {{ :​knxnet_ip_3.png?​direct800 |Editing the KNX settings}} {{ :​knxnet_ip_3.png?​direct800 |Editing the KNX settings}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​4: Editing the KNX settings</​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​5: Editing the KNX settings</​WRAP> ​ </​WRAP>​
  
 The below parameters are available to configure: The below parameters are available to configure:
Line 73: Line 76:
  
 {{ :​knxnet_ip_4.png?​direct800 |Scanning server from ETS}} {{ :​knxnet_ip_4.png?​direct800 |Scanning server from ETS}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​5: Scanning server from ETS</​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​6: Scanning server from ETS</​WRAP> ​ </​WRAP>​
  
 ===== Application 2: Thinknx server as KNXnet/IP Router ===== ===== Application 2: Thinknx server as KNXnet/IP Router =====
Line 80: Line 83:
 <WRAP column half> <WRAP column half>
 {{ :​knxnet_ip_5b.png?​direct500 |Installation without KNXNet/IP routing}} {{ :​knxnet_ip_5b.png?​direct500 |Installation without KNXNet/IP routing}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​6-a: Installation without KNXNet/IP routing</​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​7-a: Installation without KNXNet/IP routing</​WRAP> ​ </​WRAP>​
 </​WRAP>​ </​WRAP>​
 <WRAP column half> <WRAP column half>
 {{ :​knxnet_ip_5c.png?​direct500 |Installation with KNXNet/IP routing}} {{ :​knxnet_ip_5c.png?​direct500 |Installation with KNXNet/IP routing}}
-<WRAP center 60%> <WRAP centeralign>​ Figure ​6-b: Installation with KNXNet/IP routing</​WRAP> ​ </​WRAP>​+<WRAP center 60%> <WRAP centeralign>​ Figure ​7-b: Installation with KNXNet/IP routing</​WRAP> ​ </​WRAP>​
 </​WRAP>​ </​WRAP>​
 </​WRAP>​ </​WRAP>​