Differences

This shows you the differences between two versions of the page.

--- pbx_doorcom [2019/07/22 08:18] – ingrid
+++ pbx_doorcom [2019/07/22 16:12] – [Integration example: Mobotix T25 doorstation] ingrid
@@ Line 205: / Line 205: @@
 Enter the IP Address of the door station into your web browser and login using your admin username and password. You will be redirected to the live page of the camera with a main menu to the left.
 Press the “Admin Menu” button to access the administration settings.
 Scroll down through the list to reach the section called “Audio and VoIP Telephony.
-{{ :mx_admin_SIPmenu.png?direct&600 |}}
+{{ :mx_admin_SIPmenu.png?direct&800 |}}
 **SIP Server**
 Click on “SIP Server Settings”.
-Once inside the page, make sure that SIP Server is OFF. We will not need to activate this since the SIP server used will be the Thinknx server.
+Once inside the page, make sure that the internal SIP Server of Mobotix is OFF. We will not need to activate this since the SIP server used will be the Thinknx server.
+{{ :mx_SIP_server.png?direct&800 |}}
 **SIP Clients**
@@ Line 225: / Line 230: @@
   * Leave the Register Expiration as 5 min.
-{{ :mx_client_settings1.png?direct&600 |}}
+{{ :mx_sip_client1.png?direct&800 |}}
 Scroll down through the settings till you reach the Audio Codec Settings.
-Make sure that you enable “Use PCMA Codec” and “Use PCMU Codec”.
+Make sure that you enable “Use PCMA Codec” and “Use PCMU Codec”, and disable "Use G.722 Codec".
-{{ :mx_client_settings2.png?direct&600 |}}
+{{ :mx_SIP_client2.png?direct&800 |}}
-Under Video Settings, enable “Video” and choose option H.264 as your “Preferred Codec”.
+<WRAP center important round 80%> If you are unable to view the parameters above, make sure that you scroll down to the "Setup Mode" and select "Expert Setup". </WRAP>
-{{ :mx_client_settings3.png?direct&600 |}}
+{{ :mx_SIP_client3.png?direct&800 |}}
 **Configure Outgoing Calls**
@@ Line 243: / Line 248: @@
 To create the profile, click on “Add new profile”.
-Add the extension 9001 as Phone Number or SIP Address. Choose as SIP Proxy the option which follows the following template [IP_Thinknx_Server] (9001@IP_Thinknx_Server).
+{{ :mx_outgoing_call.png?direct&800 |}}
+Add the extension 9001 as Phone Number or SIP Address. Under "SIP Proxy", select the option whith the following template "IP_Thinknx_Server(9001@IP_Thinknx_Server)".
 For “Connection type”, choose “SIP Audio”.
@@ Line 257: / Line 264: @@
 Once inside, look for “Event Control” and click on “Action Group Overview”.
+{{ :mx_setup_menu.png?direct&800 |}}
 Click on “Add new group” to create a new entry and name it “Button” or “Bell Button”.
+{{ :mx_action_group.png?direct&800 |}}
 Click on Edit to configure the newly created entry.
@@ Line 266: / Line 277: @@
 Under Actions, click on “Add new action” and select the action “Phone Call: call_1”. This will allow you to call the extension configured in the Outgoing Call.
+{{ :mx_action_button.png?direct&800 |}}
+<WRAP center round important 80%> It is recommended to tune the microphone and speaker volume on the Mobotix intercom for a good quality call. This can be done by going to the Admin Menu and clicking on "Speaker and Microphone" under "Audio and VoIP Telephony". </WRAP>
+<WRAP center round important 80%> Once the configuration is completed, do not forget to store the settings on the Mobotix device. This can be done by going to the Admin Menu and scrolling down to the bottom where you will see the option "Store". A reboot will need to take place after storing. </WRAP>
+{{ :mx_admin_main.png?direct&800 |}}