Comandi interni e stati

This command is used to send a 1 bit value to the KNX bus.

• KNX Group Indirizzo di gruppo a cui inviare il valore.
• KNX value Can be either 1 or 0.

This command is used to send a 1 byte value to the KNX bus.

• KNX Group Indirizzo di gruppo a cui inviare il valore.
• KNX value Can be a value between 0-255.

A generic button can be configured to send a fixed dimming value to a dimming circuit, for example sending the value 128 to make the light go to 50%.

This command is used to send a 2 byte float value to the KNX bus.

• KNX Group Indirizzo di gruppo a cui inviare il valore.
• KNX value Can be a value between -671088,64 and 670760,96.

A generic button can be configured to send a fixed temperature value to a thermostat, for example sending the value 21.5 as a setpoint.

This command is used to send a 4 byte float value to the KNX bus.

• KNX Group Indirizzo di gruppo a cui inviare il valore.
• KNX value

This command is used to send a string of 14 bytes to the KNX bus.

• KNX Group Indirizzo di gruppo a cui inviare il valore.
• KNX value string text to be entered.

This command is used to send a 4 bit value to the KNX bus.

• KNX Group Indirizzo di gruppo a cui inviare il valore.
• KNX value Can be a value between 0 and 15.

A generic button can be configured to decrease (value 0-7) or increase ( value 8-15) a light dimming value. It can also be used to change a shutter position (use values 0-7 for UP, and 8-15 for DOWN). For example, sending the value 5 to a dimmer will decrease the brightness by 6%, while sending the value 10 to a shutter will lower its position by 50%.

This command is used to read a value from the KNX bus.

• KNX Group Indirizzo di gruppo da cui leggere il valore.

This command pauses the system for a specified time interval configurable in milliseconds.

• Interval Intervallo di tempo in millisecondi.

When saving a scene, sometimes a pause between two commands is necessary, for example, when saving the TV channel number. Another use of the Pause application would be before turning off the final light in a Goodbye scene, making sure that the client has left the house.

This command allows to redirect all clients to a specific function and page.

• Function insert the Index number of the destination function.
• Page insert the Index number of the destination page.

Using the Universal Gateway, a scenario can be configured to redirect the users to the Main Entrance camera page whenever the doorbell rings.

This command allows the specific client who has sent it to access a certain function and page.

• Function insert the Index number of the destination function.
• Page insert the Index number of the destination page.

Invisible generic buttons can be placed on the house plan for each room, allowing every single client to navigate through the rooms by clicking on each area.

This command allows to send push notifications to the clients. By accessing the web page of the server and clicking on Server –> Licenses and Codes, it is possible to enable/disable the receipt of push notifications for each client.

• Message insert the message to be displayed on the clients.
• Maximum number of push notifications with the same identifier allowed in 10 min This parameter is not mandatory. However, if a value has been entered, the system will make sure to limit the number of push notifications sent to this number in 10 min. It is quite useful when the trigger for sending the push notifications is being sent frequently on the bus.
• Push Notification Identifier A small descriptive text to allow the system to differentiate a push notification from another one when calculating the rate limit. Mandatory only if the previous parameter has been used.

Using the Universal Gateway, a push notification can be sent to the client when a 1-bit value is received from the bus to indicate that the Water Tank Level is low. The message in that case can be “Low Water Level!”. If the 1-bit is being sent periodically to the bus with a small interval, then a maximum number of push notifications can be inserted in the related parameter.

This command allows to launch an .exe file directly from the ThinKnx application on all Players for Windows.

• Command
• Parameter

Example: to open a specific file or folder on Windows, fill the Command field with “explorer.exe”, and put the entire path leading to the folder or file in the Parameter field.

This command allows to launch an .exe file directly from the ThinKnx application on all Players for Windows.

• Command
• Parameter

Example: to open a specific file or folder on Windows, fill the Command field with “explorer.exe”, and put the entire path leading to the folder or file in the Parameter field.

This property allows to launch a specific application on iOS devices directly from the ThinKnx app by typing the related URL.

• URL used to recall iOS app Type in the correct URL to open the desired installed application, for example http://www.google.com will automatically browse the google safari page. Another example is typing sonos:// to open the SONOS app.

A generic button can be configured for the client to open another application on the iOS device.

This command allows to send an email message using a default ThinKnx account.

• Email Subject Enter the email title here.
• Email Recipients Enter destination email accounts.
• Email Content Enter the email content here.

If the client's house is empty and a presence has been detected inside (1-bit KNX telegram), a scenario can be programmed on the Universal Gateway to send an email to the owner of the house.

This command might not work properly. Instead, add an Email Account under System tab, and select the command “send email to recipient” that can be found in the Internal Services. See this section for more information.

This command allows to send a DTMF tone used in telephony while an intercom call is running on the client.

• DTMF tones sequence enter the sequence of numbers to send during the intercom call. Sometimes it is necessary to end the sequence with the symbol “#”, depending on the application.

A generic button can be configured in the Intercom page to send a DTMF tone to open the main gate whenever a call is established.

When using the Thinknx server as PBX, it is possible to make internal calls between all the devices.

• Extension to call Enter the extension of the destination device.

A house owner can have a generic button on his application to call the extension of the touch screen installed in Kitchen to communication with the help.

This command allows to play an audio sound in all the clients.

• Sound to play Choose between different beeps to play: 0=Beep_1, 1=Beep_2, 2=Alarm_1, 3=Alarm_2, 4=Siren_1, 5=Siren_2.
• Duration of the sound to play Specify the duration of the sound to play in seconds. If 0 is entered, the sound will play endlessly until a Stop command has been sent.

An emergency push button can be installed in bathrooms to send a KNX 1-bit value. Using the Universal Gateway, this value received can launch the command to start audio notification on all clients.

This command allows to stop the audio sound previously launched in all clients.
See above command for example.

This command allows to start turn on or off the Hue element.

• Value Scrivere 1 per accendere e 0 per spegnere.

This command allows to set the desired value for the dimmer through a single parameter which can assume a valore compreso tra 0 e 255.

• Value can be between 0 and 255.

This command allows to set the element color temperature.

• Value Can be between 0 and 255, where 0 corresponds to Cold White (6500 K) and 255 correspond to Warm White (2000 K).

Set the element RGB color through the definition of three parameters for Red, Green and Blue. Each color can assume a valore compreso tra 0 e 255.

• Red Value valore compreso tra 0 e 255.
• Green Value valore compreso tra 0 e 255.
• Blue Value valore compreso tra 0 e 255.

This function is used to send a value to a Modbus device supporting function 5, known as “write single coil”.

• Modbus address Indirizzo Modbus.
• Coil Address Discrete output address (coils are 1-bit registers).
• Value could be 1 or 0.

This function is used to send a value to a Modbus device supporting function 6, known as “Write Single Holding Register”.

• Modbus Address Indirizzo Modbus.
• Register Address Slave register.
• Value valore da scrivere.
• N.Byte Numero di byte.

This function is used to send a value to a Modbus device supporting function 16, known as “Write Multiple Holding Registers”.

• Modbus Address Indirizzo Modbus.
• First Register Address Slave register.
• Value valore da scrivere.
• N.Byte Numero di byte.

This function is used to send a value to a Modbus device supporting function 22. The function can be used to set or clear individual bits in the register.

• Modbus Address Indirizzo Modbus.
• Register Address Slave register.
• Value valore da scrivere.
• Selected bits mask mask value of the selected bits to be changed.

This command is used to simulate a keypad button press on one of the Lutron devices installed.

• System address of the keypad Address of the keypad with the desired button to simulate. Communication is done by connecting to the Lutron processor. Address shall be written using the following template “processor:link:address”.
• Button number to operate Number of the button to press on the Lutron keypad.

This command is used to simulate a keypad button release on one of the Lutron devices installed.

• System address of the keypad Address of the keypad with the desired button to simulate. Communication is done by connecting to the Lutron processor. Address shall be written using the following template “processor:link:address”.
• Button number to operate Number of the button to release on the Lutron keypad.

This command is used to simulate a keypad button hold on one of the Lutron devices installed.

• System address of the keypad Address of the keypad with the desired button to simulate. Communication is done by connecting to the Lutron processor. Address shall be written using the following template “processor:link:address”.
• Button number to operate Number of the button to hold on the Lutron keypad.

This command is used to simulate a keypad button double tap on one of the Lutron devices installed.

• System address of the keypad Address of the keypad with the desired button to simulate. Communication is done by connecting to the Lutron processor. Address shall be written using the following template “processor:link:address”.
• Button number to operate Number of the button to double tap on the Lutron keypad.

This command is used to control Lutron shutters/blinds through a Sivoia control device.

• System address of Sivoia Control Address of the Sivoia Control device. Communication is done by connecting to the Lutron processor. Address shall be written using the following template “processor:link:address”.
• Sivoia state to select O=open, C=close, S=stop.

This command is used to play a scene configured with Lutron Grafik Eye system.

• System address of Grafik Eye to control Address of the Grafik Eye device. Communication is done by connecting to the Lutron processor. Address shall be written using the following template “processor:link:address”.
• Scene number to select Input the scene number (0=OFF).

This command is used to send the lights to a certain level.

• Output integration ID ID of the output to control.
• Level Input a number between 0 and 255 to send the lighting level.

This command is used to start raising the lighting level of the desired output.

• Output integration ID ID of the output to control.

This command is used to start lowering the lighting level of the desired output.

• Output integration ID ID of the output to control.

This command is used to stop raising/lowering the lighting level of the desired output.

• Output integration ID ID of the output to control.

This command is used to send a text without termination.

• String to send input the string that will be sent to the serial gateway.

This command is used when sending a text with CR termination, marking the end of the line.

• String to send input the string that will be sent to the serial gateway.

This command is used to send an hexadecimal string without termination.

• String to send input the string that will be sent to the serial gateway.

This command is used when sending an hexadecimal string with CR termination, marking the end of the line.

• String to send input the string that will be sent to the serial gateway.

This command allows the sending of an HTTP GET request to execute a command.

• URL
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP GET request execute a command.

• URL
• Username used to authenticate to the server
• Password used to authenticate to the server
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP POST request to send data to a certain server in order to execute a command.

• URL
• Content to send into call multiple form fields and values can be sent via the same URL. The encoding used by default is based on an early version of the general URI percent-encoding rules, with a number of modifications such as newline normalization and replacing spaces with + instead of %20. The media type of data encoded this way is application/x-www-form-urlencoded.
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP POST request to send data to a certain server in order to execute a command. The server in this case requires a username and password.

• URL
• Content to send into call multiple form fields and values can be sent via the same URL. The encoding used by default is based on an early version of the general URI percent-encoding rules, with a number of modifications such as newline normalization and replacing spaces with + instead of %20. The media type of data encoded this way is application/x-www-form-urlencoded.
• Username used to authenticate to the server.
• Password used to authenticate to the server.
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP PUT request to send data to a certain server in order to execute a command.

• URL
• Content to send into call multiple form fields and values can be sent via the same URL. The encoding used by default is based on an early version of the general URI percent-encoding rules, with a number of modifications such as newline normalization and replacing spaces with + instead of %20. The media type of data encoded this way is application/x-www-form-urlencoded.
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP PUT request to send data to a certain server in order to execute a command. The server in this case requires a username and password.

• URL
• Content to send into call multiple form fields and values can be sent via the same URL. The encoding used by default is based on an early version of the general URI percent-encoding rules, with a number of modifications such as newline normalization and replacing spaces with + instead of %20. The media type of data encoded this way is application/x-www-form-urlencoded.
• Username used to authenticate to the server.
• Password used to authenticate to the server.
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP DELETE request to send data to an external server.

• URL
• Content to send into call multiple form fields and values can be sent via the same URL. The encoding used by default is based on an early version of the general URI percent-encoding rules, with a number of modifications such as newline normalization and replacing spaces with + instead of %20. The media type of data encoded this way is application/x-www-form-urlencoded.
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of an HTTP DELETE to an external server. The server in this case requires a username and password.

• URL
• Content to send into call multiple form fields and values can be sent via the same URL. The encoding used by default is based on an early version of the general URI percent-encoding rules, with a number of modifications such as newline normalization and replacing spaces with + instead of %20. The media type of data encoded this way is application/x-www-form-urlencoded.
• Username used to authenticate to the server.
• Password used to authenticate to the server.
• Timeout for connection in milliseconds, default 3000 ms.

This command allows the sending of a string to a TCP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

This command allows the sending of a string with CR termination, marking the end of the line, to a TCP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

This command allows the sending of an hexadecimal string to a TCP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

To send “hello world”, it is enough to convert this ASCII text to HEX using a simple tool such as https://www.rapidtables.com/convert/number/ascii-to-hex.html, and the HEX string to send would be “68 65 6c 6c 6f 20 77 6f 72 6c 64”.

This command allows the sending of a string with CR termination, marking the end of the line, to a TCP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

To send “hello world”, it is enough to convert this ASCII text to HEX using a simple tool such as https://www.rapidtables.com/convert/number/ascii-to-hex.html, and the HEX string to send would be “68 65 6c 6c 6f 20 77 6f 72 6c 64”.

This command allows the sending of an hexadecimal string to a UDP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

This command allows the sending of a string with CR termination, marking the end of the line, to a UDP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

This command allows the sending of an hexadecimal string to a UDP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

To send “hello world”, it is enough to convert this ASCII text to HEX using a simple tool such as https://www.rapidtables.com/convert/number/ascii-to-hex.html, and the HEX string to send would be “68 65 6c 6c 6f 20 77 6f 72 6c 64”.

This command allows the sending of a string with CR termination, marking the end of the line, to a UDP host on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

To send “hello world”, it is enough to convert this ASCII text to HEX using a simple tool such as https://www.rapidtables.com/convert/number/ascii-to-hex.html, and the HEX string to send would be “68 65 6c 6c 6f 20 77 6f 72 6c 64”.

This command allows the sending of an hexadecimal string to a UDP host supporting multicast on a defined port. The characters should be separated by a space.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

To send “hello world”, it is enough to convert this ASCII text to HEX using a simple tool such as https://www.rapidtables.com/convert/number/ascii-to-hex.html, and the HEX string to send would be “68 65 6c 6c 6f 20 77 6f 72 6c 64”.

This command allows the sending of a string with CR termination, marking the end of the line, to a UDP host supporting multicast on a defined port.

• String to send
• Host:port
• Timeout for connection in milliseconds, default 3000 ms.
• Time to wait before closing connection after data sending in milliseconds, default 100 ms.

To send “hello world”, it is enough to convert this ASCII text to HEX using a simple tool such as https://www.rapidtables.com/convert/number/ascii-to-hex.html, and the HEX string to send would be “68 65 6c 6c 6f 20 77 6f 72 6c 64”.

This command allows the sending of a SOAP (Simple Object Access Protocol) request to a URL. SOAP is an XML-based messaging protocol for exchanging information among computers.

• URL
• SOAP Envelope Defines the start and the end of the message. It is a mandatory element.
• SOAP Action indicates the intent of the SOAP HTTP request.

This command allows to establish an SSH session with a server to execute certain commands. Secure Socket Shell or SSH, is a network protocol that gives users, particularly system administrators, a secure way to access a computer over an unsecured network.

• SSH server hostname
• SSH server port
• Username
• Password
• Commands to send Commands must be enclosed in double quotes and separated by a space, example: “cmd one” “cmd two” “etc”

Application: This session can be used to connect to the home router/access point through Thinknx.

This command allows launching of a scenario configured on the MyHome system.

• Scenario Number as configured in MyHome.
• Control Panel
• Interface (I)

This command allows to send an ON or OFF command to one lighting point.

• Room (A) as configured in MyHome.
• Light Point (PL)
• Interface (I)
• ON/OFF type 0 to turn off and 1 to turn on.

This command allows to send a dimming value to one dimmer.

• Room (A) as configured in MyHome.
• Light Point (PL)
• Interface (I)
• Dimmer Level type a value between 0 and 255 for dimmer's level.

This command allows to send an ON value duration for one light point.

• Room (A) as configured in MyHome.
• Light Point (PL)
• Interface (I)
• ON timed for (min) the values can be 0.5, 1, 2, 3, 4,5, or 15 min.

This command allows to send an ON or OFF command to an entire room.

• Room (A) as configured in MyHome.
• Interface (I)
• ON/OFF type 0 to turn off and 1 to turn on.

This command allows to send an ON value duration for an entire room.

• Room (A) as configured in MyHome.
• Interface (I)
• ON timed for (min) the values can be 0.5, 1, 2, 3, 4,5, or 15 min.

This command allows to send an ON or OFF command to a group of lighting points.

• Group as configured in MyHome.
• Interface (I)
• ON/OFF type 0 to turn off and 1 to turn on.

This command allows to send a dimming value to a group of lighting points.

• Group as configured in MyHome.
• Interface (I)
• Dimmer Level type a value between 0 and 255 for dimmer's level.

This command allows to send an ON value duration for a group of lighting points.

• Group as configured in MyHome.
• Interface (I)
• ON timed for (min) the values can be 0.5, 1, 2, 3, 4,5, or 15 min.

This command allows to send an ON or OFF command to all lighting points.

• ON/OFF type 0 to turn off and 1 to turn on.

This command allows to send a dimming value to all lighting points.

• Dimmer Level type a value between 0 and 255 for dimmer's level.

This command allows to send an ON value duration for all lighting points.

• ON timed for (min) the values can be 0.5, 1, 2, 3, 4,5, or 15 min.

This command allows to control a single shutter by sending Up, Down or Stop.

• Room (A) as configured in MyHome.
• Automation Point (PL)
• Interface (I)
• Stop/Up/Down Stop=0, Up=1, Down=2.

This command allows to control a group of shutters by sending Up, Down or Stop.

• Group as configured in MyHome.
• Interface (I)
• Stop/Up/Down Stop=0, Up=1, Down=2.

This command allows to control all shutters in a single room.

• Room as configured in MyHome.
• Interface (I)
• Stop/Up/Down Stop=0, Up=1, Down=2.

This command allows to control all shutters.

• Stop/Up/Down Stop=0, Up=1, Down=2.

This command allows to change the setpoint in a zone.

• Zone (ZA, ZB) as configured in MyHome.
• Temperature type the value of the temperature in °C.

This command allows to enable/disable the thermostat.

• Zone (ZA, ZB) as configured in MyHome.
• Enable or disable type 1 to enable and 0 to disable.

This command allows to control the volume of a speaker.

• Room (A) as configured in MyHome.
• Loudspeaker (PF)
• Volume the number must be between 0 and 255.

This command allows to turn a speaker on or off.

• Room (A) as configured in MyHome.
• Loudspeaker (PF)
• ON/OFF insert 1 to turn on and 0 to turn off.

This function is used to restart the HomeKit gateway enabled from the server's web page.

This function is used to send a command from Thinknx to trigger an event configured on an IFTTT service. The service configured in this case requires certain values before execution.

• Event identification this identification should match the one entered on the IFTTT website.
• Value to pass as ingredient 1 value 1 required by the service on IFTTT.
• Value to pass as ingredient 2 value 2 required by the service on IFTTT.
• Value to pass as ingredient 3 value 3 required by the service on IFTTT.

This function is used to send a command from Thinknx to trigger an event configured on an IFTTT service.

• Event identification this identification should match the one entered on the IFTTT website.

This function allows the sending of an SMS to multiple phone numbers.

• SMS text content message body.
• Receivers phone numbers use “ ; ” to indicate more receivers. Number should be international without leading + or 00.

This command will allow to play the selected scene.

This command will allow to stop a scene during execution.

This command allows to start playing the presence simulation configured in the Presence Simulation object in System.

This command allows to stop playing the presence simulation configured in the Presence Simulation object in System.

This command allows to activate/deactivate the control of the setpoint from the schedule configured by the client.

• Enable/Disable send 1 to enable and 0 to disable.

This command allows to send an email to a group of recipients.

• Email subject
• Email recipients separate the emails using “ ; ”.
• Email content body of the email.

This command allows read the humidity value from the selected sensor

This command allows read the luminosity value from the selected sensor

This command allows read the temperature value from the selected sensor

This command allows to activate/deactivate the functioning of the irrigation zones from the schedule configured by the client.

This command allows to play a sequence of all the favorite colors in a shuffle mode, while defining the time to switch from one color to another.

• Time interval before switching to a new color, in seconds

This command allows to play a sequence of all the favorite colors in order and repeat them once done, while defining the time to switch from one color to another.

• Time interval before switching to a new color, in seconds

This command allows to stop an already launched sequence and turn off the RGB light.

This command allows to save the current color to one of the available slots in Favorites.

• Preset position number of the slot where the color should be saved (value between 0-9).

This command allows to switch the color of the RGB lights into the color saved in the requested slot below.

• Preset position number of the slot corresponding to the desired color (value between 0-9).

This command will disconnect all the inputs connected to the outputs.

This command will disconnect the input connected to the desired output.

• Output Number

This command will allow to set the desired input to a selected output.

• Input Number
• Output Number

This command will allow to set the desired input to one or more multiple outputs.

• Input Number
• Output Number use comma “,” to send to multiple outputs.

This command will allow to disconnect the inputs on all outputs.

This command will allow to mute or unmute one or more outputs.

• Output Number use comma “,” to send to multiple outputs.
• Mute Value 1=muted, 0=unmuted.

This command will allow to raise the volume on the selected output. The volume is raised by 1.

• Output Number use comma “,” to send to multiple outputs.

This command will allow to lower the volume on the selected output. The volume is lowered by 1.

• Output Number use comma “,” to send to multiple outputs.

This command will allow to set the a desired value to the volume on the selected output.

• Output Number use comma “,” to send to multiple outputs.
• Volume value between 0-100.

This command will allow to change the TV channel to the desired channel entered inside the parameter.

• Channel Number

This command will allow to set the video source on the TV.

• Source Number

This command will allow to turn ON the TV or put it to Standby mode.

• Power Value 1=Power ON, 0=Standby.

This command will allow to send a value to the TV volume.

• Volume Level value between 0-100.

This command will allow to raise the volume on the TV.

This command will allow to lower the volume on the TV.

This command will allow to turn the device On or put it to Standby mode. The command is sent to each zone individually.

• Subzone
• power value this value varies depending on the Brand of the Home Theater device. For more information, contact support@thinknx.com.

This command will allow to mute or unmute the output on the selected subzone.

• Subzone
• mute value this value varies depending on the Brand of the Home Theater device. For more information, contact support@thinknx.com.

This command will allow to raise the volume on the selected subzone.

• Subzone

This command will allow to lower the volume on the selected subzone.

• Subzone

This command will allow to send a desired value to the output's volume.

• Subzone
• Volume value between 0-100.

This command will allow to raise the bass on the output.

This command will allow to lower the bass on the output.

This command will allow to raise the treble on the output.

This command will allow to lower the treble on the output.

This command will allow to enable or disable the subwoofer.

• Sub enable

This command will allow to set the desired source to the main output of the selected zone.

• Subzone
• Main source

This command will allow to set the main audio source.

• Subzone
• Main source audio

This command will allow to set the main video source.

• Subzone
• Main source video

This command will allow to get a feedback on the current tuner frequency.

This command will allow to get a feedback on the current tuner station.

This command will allow to raise the tuner frequency.

This command will allow to lower the tuner frequency.

This command will allow to scan for the next tuner station.

This command will allow to scan for the previous tuner station.

This command will allow to launch the tuner auto search.

This command will allow to stop the tuner auto search.

This command will allow to select the digital mode on the device.

• Digital Mode

This command will allow to select the surround mode on the device.

• Digital Mode

This command will allow show/hide the on screen display menu for the remote.

• OSD Setup 1=show OSD menu, 0=hide OSD menu.

This command will simulate the remote control command “Cursor Up”.

This command will simulate the remote control command “Cursor Down”.

This command will simulate the remote control command “Cursor Right”.

This command will simulate the remote control command “Cursor Left”.

This command will simulate the remote control button “Enter”.

This command will simulate the remote control button “Back/Return”.

This command will simulate the remote control button “Option”.

This command will simulate the remote control button “Info”.

This command will allow to send a customized command to the device.

• Command to send to the device refer to the Denon/Marantz protocol specification.

This feedback will read the active input on the AVR.

This feedback will read the power status of the device.

This feedback will read the current volume set on the device.

This feedback will read the selected audio type.

This feedback will read the selected video type.

This feedback will read the text displayed on the device.

This command will allow to play music on the selected player.

This command will allow to stop the music from playing on the selected player.

This command will allow to raise the volume on the selected player.

This command will allow to lower the volume on the selected player.

This command will allow to play the next track.

This command will allow to play the previous track.

This command will allow to set the volume to a desired level.

• Desired Volume value between 0 and 100.

This command will allow to mute/unmute the player.

• Mute value 1=unmuted, 0=muted.

This command will allow to play the music coming from the analog input of the player.

This command will allow to play the music coming from the analog input of another player player.

• Zone player unique identifier this identifier can be found when accessing the Sonos Manager in System and going to the Players collection.

This command will allow to play a shared file on the network using its URL.

• File URL should follow the form ://192.168.2.5/Music/abc.mp3

This command will allow to play from a streaming URL.

• Streaming URL should follow the form ://myradiostream.com:800

This command will enable/disable the repeat mode.

• Repeat value 1=enabled, 0-disabled.

This command will enable/disable the Shuffle mode.

• Shuffle value 1=enabled, 0-disabled.

This command will start playing a desired playlist from its number.

• Playlist number

This command will start playing a desired playlist from its name.

• Playlist name

This command will start playing a desired item from the Favorite list.

• Favorite number

This feedback will read the mute status.

This feedback will read the current track album.

This feedback will read the current track artist.

This feedback will read the current track artist URL.

This feedback will read the current track title.

This feedback will read the current volume level.

This feedback will give the last invoked playlist.

This feedback will read the play status of the player.

This feedback will read if the repeat function is enabled or disabled.

This feedback will read if the shuffle function is enabled or disabled.

Simulates the $\uparrow$ command.

Simulates the $\downarrow$ command.

Simulates the $\rightarrow$ command.

Simulates the $\leftarrow$ command.

Select the current object in the user interface. (It simulates the ”OK” or ”Enter” command)

Return to the previous page; it simulates the ”Return” or ”Back” command.

Visualize the current object menu; it simulates the ”Menu” button.

Displays a pop-up with the information related to the current program; it simulates the ”Info” button.

Redirects to the GUI homepage; it simulates the ”Home” button.

Visualize a pop-up with the on-screen display for the current player.

Launches a specified file; the file path can be specified by adjusting the ”File path” parameter on the right.

Play or pause the current player.

Stops the player.

Skips the current track and directly play the next one.

Skips the current track and directly play the next one.

Fast forward the current playing element.

Fast backward the current playing element.

Turns the volume up.

Turns the volume down.

This command will allow to send an IR command by selecting it from the list to the right. If you want to select a defined output different from the default one, before enqueuing the command, it is possible to enable the “Output option” and select the desired output from the list. The enqueued command will appear on the list of the commands to execute with an appended index corresponding to the selected output. It is possible to create complex macro of IR operations simply enqueuing more commands. Commands can be separated by pause adding the ”Make pause” item in order to grant a better reception. The sequence displayed in the box on the bottom of the page can be edited by deleting single items or moving them by clicking on ”Up” and ”Down” buttons.

This command will allow to arm one partition using its related pin code.

• Partition Number
• Pin Code

This command will allow to disarm one partition using its related pin code.

• Partition Number
• Pin Code

This command will allow to arm all partition using a common pin code.

• Pin Code

This command will allow to disarm all partition using a common pin code.

• Pin Code

This command will allow to control a particular output on the alarm system.

• Number of the output to switch
• New /state of the output ON=1, OFF=0.

This command will allow to arm one partition using its related pin code.

• Partition Number
• Pin Code

This command will allow to disarm one partition using its related pin code.

• Partition Number
• Pin Code

This command will allow to arm all partition using a common pin code.

• Pin Code

This command will allow to disarm all partition using a common pin code.

• Pin Code

This command will allow to control a particular output on the alarm system.

• Number of the output to switch
• New /state of the output ON=1, OFF=0.