Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
alarm_device [2019/03/20 17:04] – external edit 127.0.0.1 | alarm_device [2020/08/18 11:39] – ingrid | ||
---|---|---|---|
Line 31: | Line 31: | ||
* // | * // | ||
* //TCP_IP:// Connected through network link.\\ If the property ”Communication” is set to ”RS232”, | * //TCP_IP:// Connected through network link.\\ If the property ”Communication” is set to ”RS232”, | ||
- | * Serial Port: This property represents | + | * Serial Port: Serial port number that changes depending on the server used. Click [[port_numbers| here]] to get the correct |
* IP Address: Device IP address or RS232overIP address. | * IP Address: Device IP address or RS232overIP address. | ||
* Port Number: TCP/IP port number for ethernet connection. | * Port Number: TCP/IP port number for ethernet connection. | ||
Line 51: | Line 51: | ||
* Passphrase: Encryption passphrase used during panel configuration. | * Passphrase: Encryption passphrase used during panel configuration. | ||
+ | ==== Object Commands ==== | ||
+ | After adding an alarm device to the system, it is possible to send a number of commands when using other objects such as the Generic Command button. | ||
+ | |||
+ | <WRAP centeralign> | ||
+ | |||
+ | After selecting **Security** from the tree, a list of all the alarm devices and centrale added in System will be shown. The available commands when selecting one of the devices are the following: | ||
+ | |||
+ | ++++Arm a particular partition with a specified code| This command will allow to arm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm a particular partition with a specified code| This command will allow to disarm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Arm all partitions with a specified code| This command will allow to arm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm all partitions with a specified code| This command will allow to disarm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Switch ON or OFF the specified output| | ||
+ | * **Number of the output to switch** | ||
+ | * **New /state of the output** ON=1, OFF=0. | ||
+ | ++++ | ||
+ | |||
+ | === Centrale === | ||
+ | After selecting **Security** from the tree, a list of all the alarm devices and centrale added in System will be shown. The available commands when selecting one of the devices are the following: | ||
+ | |||
+ | ++++Arm a particular partition with a specified code| This command will allow to arm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm a particular partition with a specified code| This command will allow to disarm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Arm all partitions with a specified code| This command will allow to arm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm all partitions with a specified code| This command will allow to disarm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Switch ON or OFF the specified output| | ||
+ | * **Number of the output to switch** | ||
+ | * **New /state of the output** ON=1, OFF=0. | ||
+ | ++++ | ||
==== Bentel Interface ==== | ==== Bentel Interface ==== | ||