Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revisionLast revisionBoth sides next revision | ||
alarm_device [2019/03/20 17:04] – external edit 127.0.0.1 | alarm_device [2023/02/27 13:56] – ingrid | ||
---|---|---|---|
Line 2: | Line 2: | ||
{{ : | {{ : | ||
+ | |||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | * [[# | ||
+ | ==== Alarm Object ==== | ||
This object is used to integrate the central alarm in the project; it allows the server to arm or disarm the central, to read partitions or sensor status and to singularly control them. All alarm panels integrated in the system provide the user with the same graphical effect; they can be selected from the following list of models: | This object is used to integrate the central alarm in the project; it allows the server to arm or disarm the central, to read partitions or sensor status and to singularly control them. All alarm panels integrated in the system provide the user with the same graphical effect; they can be selected from the following list of models: | ||
* **Device type** This property allows to select the alarm panel model. | * **Device type** This property allows to select the alarm panel model. | ||
+ | |||
+ | <WRAP group> | ||
+ | <WRAP column half> | ||
+ | * //ArrowHead Elit SX// | ||
* //AVS Electronics XTream 640// | * //AVS Electronics XTream 640// | ||
* //Bentel Absoluta// | * //Bentel Absoluta// | ||
Line 15: | Line 30: | ||
* //Brahms series B4 CMP64// | * //Brahms series B4 CMP64// | ||
* //Elkron MP508 TG// | * //Elkron MP508 TG// | ||
+ | * //Elmo (ETRx, ET8plus, NETx, Villegio, Pregio, Tacora)// | ||
* //GE security/ | * //GE security/ | ||
+ | * //GE security/ | ||
* //Honeywell Galaxy Dimension// | * //Honeywell Galaxy Dimension// | ||
+ | * //Iess (Genio)// | ||
+ | </ | ||
+ | <WRAP column half> | ||
+ | * //Inim Prime webAPI// | ||
* //Inim Smartliving 10100// | * //Inim Smartliving 10100// | ||
* //Inim Smartliving 1050// | * //Inim Smartliving 1050// | ||
* //Inim Smartliving 515// | * //Inim Smartliving 515// | ||
+ | * //Paradox EVO// | ||
* //Rokonet RP128// | * //Rokonet RP128// | ||
* //Rokonet RP128 BRTE// | * //Rokonet RP128 BRTE// | ||
+ | * //Satel Integra// | ||
* //Siemens SPC// | * //Siemens SPC// | ||
* // | * // | ||
+ | * // | ||
* // | * // | ||
* // | * // | ||
* //Urmet 1067// | * //Urmet 1067// | ||
+ | * //Wago Switzerland// | ||
+ | </ | ||
+ | </ | ||
* **Communication: | * **Communication: | ||
* //RS232:// Connected through serial cable. | * //RS232:// Connected through serial cable. | ||
* // | * // | ||
* //TCP_IP:// Connected through network link.\\ If the property ”Communication” is set to ”RS232”, | * //TCP_IP:// Connected through network link.\\ If the property ”Communication” is set to ”RS232”, | ||
- | * Serial Port: This property represents | + | * Serial Port: Serial port number that changes depending on the server used. Click [[port_numbers| here]] to get the correct |
* IP Address: Device IP address or RS232overIP address. | * IP Address: Device IP address or RS232overIP address. | ||
* Port Number: TCP/IP port number for ethernet connection. | * Port Number: TCP/IP port number for ethernet connection. | ||
Line 50: | Line 77: | ||
* Users: List of security users associated to this control.\\ If in the property ”Device Type” are selected ”Tecnoalarm TP16-256”, | * Users: List of security users associated to this control.\\ If in the property ”Device Type” are selected ”Tecnoalarm TP16-256”, | ||
* Passphrase: Encryption passphrase used during panel configuration. | * Passphrase: Encryption passphrase used during panel configuration. | ||
+ | |||
+ | ==== Object Commands ==== | ||
+ | After adding an alarm device to the system, it is possible to send a number of commands when using other objects such as the Generic Command button. | ||
+ | |||
+ | <WRAP centeralign> | ||
+ | |||
+ | After selecting **Security** from the tree, a list of all the alarm devices and centrale added in System will be shown. The available commands when selecting one of the devices are the following: | ||
+ | |||
+ | ++++Arm a particular partition with a specified code| This command will allow to arm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm a particular partition with a specified code| This command will allow to disarm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Arm all partitions with a specified code| This command will allow to arm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm all partitions with a specified code| This command will allow to disarm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Switch ON or OFF the specified output| | ||
+ | * **Number of the output to switch** | ||
+ | * **New /state of the output** ON=1, OFF=0. | ||
+ | ++++ | ||
+ | |||
+ | === Centrale === | ||
+ | After selecting **Security** from the tree, a list of all the alarm devices and centrale added in System will be shown. The available commands when selecting one of the devices are the following: | ||
+ | |||
+ | ++++Arm a particular partition with a specified code| This command will allow to arm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm a particular partition with a specified code| This command will allow to disarm one partition using its related pin code. | ||
+ | * **Partition Number** | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Arm all partitions with a specified code| This command will allow to arm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Disarm all partitions with a specified code| This command will allow to disarm all partition using a common pin code. | ||
+ | * **Pin Code** | ||
+ | ++++ | ||
+ | |||
+ | ++++Switch ON or OFF the specified output| | ||
+ | * **Number of the output to switch** | ||
+ | * **New /state of the output** ON=1, OFF=0. | ||
+ | ++++ | ||
+ | |||
+ | ==== Adding partitions ==== | ||
+ | |||
+ | Click on the button displayed on the right to open partitions editor window, click on ”Add” and then adjust the properties in the grid: | ||
+ | |||
+ | * **Area Name** Label of text to identify the area. | ||
+ | * **Central index** Insert the number of the partition programmed in the security system. | ||
+ | * **Disarming** Enable/ | ||
+ | * **Arming** Enable/ | ||
+ | * **Command bit** KNX group address to command arming of the area (1 bit - 1=arm, 0=disarm) | ||
+ | * **Command Byte** KNX group address to command area in byte. | ||
+ | * **Command 14 Byte** KNX group address to command area in with 14 bytes object. The string should be in the form 1|xxxx or 0|xxxx where xxxx represents the user code and 0 or 1 is used to decide if the partition should be armed or disarmed. | ||
+ | * **Status byte** 1 byte KNX group address sent by the server containing the partition status. | ||
+ | * **Area name** Insert the partition name. | ||
+ | |||
+ | ==== Adding sensors ==== | ||
+ | |||
+ | Click on the button displayed on the right to open sensors editor window, click on ”Add” and then adjust the properties in the grid: | ||
+ | |||
+ | * **Index number** Insert the number of the sensor you programmed in your security system. | ||
+ | * **Group** Insert a KNX group address to communicate with the sensor (f.e. to turn on a light using an alarm system motion sensor). | ||
+ | * **Name of the sensor** Sensor name. | ||
+ | * **Send all states** If enabled, the sensor sends all states, if disabled, the sensor sends only alarm state (only value 1). | ||
+ | * **Send on change** If enabled the sensor sends its state only on change (otherwise, sensor status will be sent on every polling). | ||
==== Bentel Interface ==== | ==== Bentel Interface ==== | ||
Line 90: | Line 197: | ||
{{ : | {{ : | ||
- | ==== Adding partitions | + | ==== Paradox Evo ==== |
- | Click on the button displayed on the right to open partitions editor window, click on ”Add” | + | To interact with a Paradox Evo device, |
+ | {{ :paradox_PRT3.png? | ||
- | * **Area Name** Label of text to identify | + | To ensure correct communication with the Thinknx server, |
- | * **Central index** Insert | + | * Set Baud Rate: 57600 |
- | * **Disarming** Enable/ | + | * Set Printer Module' |
- | * **Arming** Enable/ | + | |
- | * **Command bit** KNX group address to command arming of the area (1 bit - 1=arm, 0=disarm) | + | |
- | * **Command Byte** KNX group address to command area in byte. | + | |
- | * **Command 14 Byte** KNX group address to command area in with 14 bytes object. The string should be in the form 1|xxxx | + | |
- | * **Status byte** 1 byte KNX group address sent by the server containing the partition status. | + | |
- | * **Area name** Insert the partition name. | + | |
- | ==== Adding sensors | + | {{ : |
+ | |||
+ | To properly connect the device to the Thinknx server, see below diagram: | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | ==== Inim Prime webAPI | ||
+ | To interact with Inim Prim webAPI, it is necessary to generate an API key from the alarm' | ||
+ | |||
+ | {{ : | ||
- | Click on the button displayed on the right to open sensors editor window, click on ”Add” and then adjust the properties in the grid: | ||
- | * **Index number** Insert the number of the sensor you programmed in your security system. | ||
- | * **Group** Insert a KNX group address to communicate with the sensor (f.e. to turn on a light using an alarm system motion sensor). | ||
- | * **Name of the sensor** Sensor name. | ||
- | * **Send all states** If enabled, the sensor sends all states, if disabled, the sensor sends only alarm state (only value 1). | ||
- | * **Send on change** If enabled the sensor sends its state only on change (otherwise, sensor status will be sent on every polling). |